DESCRIPTION

AUTOTRIZ Gel Coat Coating is formulated specifically for epoxy and polyester gel coats. It is an unique Nano ceramic coating that seals your gel coat of your boat, yacht or jet by forming a high gloss protective layer with ultra smooth hydrophobic characteristic that blocks out harmful UV rays and repels acid rain, oil, fuel spills and other contaminants.

​

AUTOTRIZ Gel Coat Coating offers excellent chemical resistance that can withstand corrosion from salt water and it cannot be removed by cleaning chemicals. When spayed to hull, it helps to prevent attachment of microorganisms by slowing down the growth and/or facilitate detachment of sub-aquatic organisms that attach to the hull.

PROPERTIES

- Permanent bond 

- Excellent protection against rain and sun damage

- Anti-fouling

- Minimizes marine bio
- Easy-to-Clean
- Excellent adhesion to gel coated surfaces
- Outstanding weather resistance 
- High UV and salt water resistance

- Prevents fading and oxidation
- Superior to Siloxane based coating

APPLICATION

Gel Coat Coating is particularly suitable for gel coat of boats, yachts and jet skis. 

TOOLS

Gel Coat Coating can be applied with microfiber applicators or HLVP spray gun

TECHNICAL DATA

Appearance: Colourless

​

Density: ca. 0,96 g/cm3

​

Base: Organic + Inorganic Polysilazane

​

Curing: Normal ambient temperature/ 80° celcius

​

Shelf Life: 12 months

​

Container Size: 50ml/ 1000ml

INSTRUCTIONS FOR USE

The product is for professional use and should be applied by approved applicators only. Test on a small area or apply a test coat before application.

​

APPLICATION OF GEL COAT COATING

​

Method 1 (By Hand)

Shake well before use.

​

Get ready with 2 pieces of brand new, lint-free microfiber towel. (It is recommended that new towels to be rinsed or washed with water prior to use to reduce the loosing lint)

​

When first applying Gel Coat Coating on substrate, it is recommended to condition the surface of the applicator block with 7-8 drops to prevent skipping or dry spots.

​

Do not work on large area at a time. It is recommended to do a 4 ft. x 4 ft. area at a time.

​

Apply Gel Coat Coating using normal pressure on applicator. Make sure the area is well covered. Always start from an edge to avoid excess on other panels. Work in controlled areas to remember where you previously applied. Work in horizontal or vertical movements repeatedly to ensure that product is penetrated through gel coat

​

Wait for 5-10 minutes. Use first towel to level the product.

​

Go immediately over with second microfiber towel with polishing motion until the surface is free from residue.

​

When the whole boat is applied, allow curing of coating to begin.

​

Wait approximately 30-60 minutes before applying a second layer.

​

Allow curing of coating to begin.

​

Method 2 (By Hand)

Shake well before use.

​

When first applying Gel Coating on substrate, it is recommended to condition the surface of the applicator block with 7-8 drops to prevent skipping or dry spots.

​

Do not work on large area at a time. It is recommended to do a 4 ft. x 4 ft. area at a time.

​

Apply Gel Coating using normal pressure on applicator. Make sure the area is well covered. Always start from an edge to avoid excess on other panels. Work in controlled areas to remember where you previously applied. Work in horizontal or vertical movements repeatedly to ensure that product is penetrated through gel coat

​

Leave the coating to dry and form a thin layer.

​

When the whole boat is applied, allow curing of coating to begin.

​

Wait approximately 30-60 minutes before applying a second layer.

​

Allow curing of coating to begin.

​

Method 3 (By Spray Gun)

Shake well before use.

​

Fill Gel Coat Coating into HVLP spray gun, adjust nozzles and set spraying pattern in flat.

​

Spray one layer in horizontal direction and one layer in vertical direction until the coating leaves a clear and glossy thin layer.

​

Allow curing of coating to begin. Curing can be accelerated by using infra-red lights.

​